Nickel Alloy Gasket Rings Inconel 600 EV Battery Packs Power Generation W. Nr. 2.4816
Nickel Alloy Gasket Rings, is a type of sealing component used to create a barrier between one mating surface and another to prevent the escape or ingress of fluids or gases. To accommodate these flat surfaces, the gasket can be flat or slightly curved. They can also be cut into different shapes to fit precisely between the surfaces they’re meant to seal. They can even be made to fit complex mating surfaces.
- Sealing gaskets. Available in EPDM or PVC, these sealing gaskets are typically used to form a protective edge on sheet metal. Ideal for enclosures, they simply clip onto the mating surface to protect against vibrations and ingress of humidity and dirt.
- Motor Shaft Seals. Motor Seals are used in motors,with the externalrubber whole-covering desion to ensure the outer diameter ofthe sealing efect. A rotary actuator seal can prevent the loss of pressure and ensure the normal operation of the power steering system, to achieve the sealing effect.
- Threaded Protection plug – wide flange. Gaskets are sealing elements installed between mating flange faces. The compressive force applied when flanges are mated (due to bolt torqueing) keeps the gasket in position between the two flanges. Flange gaskets are split into two main categories:
- Metallic / Hard – oval ring, octagonal ring.
- Semi-metallic / Composite – spiral wound, metal jacketed, camprofile.
Alloy 600 (UNS N06600) is a nickel-chromium alloy designed for use fromcryogenic to elevated temperatures in the range of 2000F(1093 °C) qood oxidation resistance at higher temperatures, with good resistance in carburizing andchloride containing environments. The high nickel contentof the aloy enables it to retain considerable resistance under reducing conditions and makes it resistant to corrosion by a number of organic and inorganic compounds.The nickel content gives it excellent
resistance to chloride-ion stress-corrosion cracking andalso provides excellent resistance to alkaline solutions. Its chromium content gives the alloy resistance to sulfurcompounds and various oxidizing environments. The chromium content of the alloy makes it superior to commercially pure nicke under oxidizing conditions.rstrong oxidizing solutions, like hot concentrated nitricacid,600 has poor resistance. Alloy 600 is relativelyunattacked by the majority of neutral and alkaline saltsolutions and is used in some caustic environments.
Applications
Thermocouple sheaths / Ethylene dichloride (EDC) cracking tubes / Conversion of uranium dioxide to tetrafluoride in contact with hydrofluoric acid / Production of caustic alkalis particularly in the presence of sulfur compounds / Reactor vessels and heat exchanger tubing used in the production of vinyl chloride / Process equipment used in the production of chlorinated and fluorinated hydrocarbons / Furnace retort seals, fans, and fixtures/Roller hearths and radiant tubes, especially in carbonnitriding processes / Heat treating muffles and retorts / Vacuum furnace fixtures.Chlorination equipment to 1000°F Titanium dioxide plants,
Machining:
Nickel based alloys can be difficult tomachinine.However, it should be emphasized that thesealloys can be machined using conventional productionmethods at satisfactory rates. These alloys harden rapidlygenerate high heat during cutting, weld to the cuttingtool surface and offer high resistance to metal removabecause of their high shear strengths. The following arekey points which should be considered during machining operations: capacity/tools/positive cut/lubrication.
Chemical Composition:
| Element | Ni+Co | Cr | Fe | C | Mn | S | Si | Cu |
| Minimum(%) | 72 | 14 | 6 | - | - | - | - | - |
| Max(%) | - | 17 | 10 | 0.15 | 1 | 0.015 | 0.5 | 0.5 |
Thermal Properties:
| Temperature | Coefficient of Expansiona | Electrical Resistivity | Thermal Conductivity | Specific Heat |
| °F | 10-6 in/in•°F | ohm•circ•mil/ft | Btu•in/ft2•h•°F | Btu/lb•°F |
| -250 | 6.0 | - | 86 | 0.073 |
| -200 | 6.3 | - | 89 | 0.079 |
| -100 | 6.7 | - | 93 | 0.090 |
| 70 | 5.8 | 620 | 103 | 0.106 |
| 200 | 7.4 | 625 | 109 | 0.111 |
| 400 | 7.7 | 634 | 121 | 0.116 |
| 600 | 7.9 | 644 | 133 | 0.121 |
| 800 | 8.1 | 644 | 145 | 0.126 |
| 1000 | 8.4 | 680 | 158 | 0.132 |
| 1200 | 8.6 | 680 | 172 | 0.140 |
| 1400 | 8.9 | 680 | 186 | 0.145 |
| 1600 | 9.1 | 686 | 200 | 0.149 |
| 1800 | 9.3 | 698 | - | - |
| 2000 | - | 704 | - | - |
| °C | μm/m•°C | μΩ•m | W/m•°C | J/kg•°C |
| -150 | 10.9 | - | 12.5 | 310 |
| -100 | 11.7 | - | 13.1 | 352 |
| -50 | 12.3 | - | 13.6 | 394 |
| 20 | 10.4 | 1.03 | 14.9 | 444 |
| 100 | 13.3 | 1.04 | 15.9 | 444 |
| 200 | 13.8 | 1.05 | 17.3 | 486 |
| 300 | 14.2 | 1.07 | 19.0 | 502 |
| 400 | 14.5 | 1.09 | 20.5 | 519 |
| 500 | 14.9 | 1.12 | 22.1 | 536 |
| 600 | 15.3 | 1.13 | 22.1 | 578 |
| 700 | 15.8 | 1.13 | 25.7 | 595 |
| 800 | 16.1 | 1.13 | 27.5 | 611 |
| 900 | 16.4 | 1.15 | - | 628 |
| Physical Properties |
| Mean Coefficient of Thermal Expansion |
| Temperature Range |
| °F | °C | in/in°F | cm/cm°C |
| 68 | 20 | 5.8 x 10-6 | 10.4 x 10-6 |
| Mechanical Properties |
| Typical Values at 68°F(20°C) |
| Yield Strength 0.2% offset psi | Ultimate Tensile Strength (min.) psi | Elongation in 2"% |
| 35,000 | 80,000 | 30 |
Processing Flow Chart:
Product Tags:
|
|
Inconel 600 Nickel Alloy Gasket Rings For Power Generation W. Nr. 2.4816 Images
|
